Tri-tool 230B Miter Mandrel User Manual

92-0841 Rev. 050317Model 230B Miter MandrelTABLE OF CONTENTSCUSTOMER MESSAGE Inside Front CoverSAFETY PRECAUTIONS 3GENERAL DESCRIPTION 6SPECIFICATIO

10TRI TOOL INC.92-0841 : Rev. 050317Weekly maintenance should include checking the mandrel, wiping the oil and grimefrom the surface and then relubric

11Model 230B Miter Mandrel92-0841 : Rev. 050317CAUTION:OPERATIONNever attempt to manually lift the Mandrel with the Powerhead installed.The eight (8)

12TRI TOOL INC.92-0841 : Rev. 050317NOTE:NOTE:To make the Parallel Offset Adjustment, all four (4) screws must be slightlyloose.Install the Mandrel Sh

13Model 230B Miter Mandrel92-0841 : Rev. 050317All screws must be at least slightly loose to allow movement.Angular Offset AdjustmentUneven GapDraw Sc

14TRI TOOL INC.92-0841 : Rev. 050317NOTE:If the Mandrel Shaft is to be drawn directly toward one screw, the oppositescrew must be loosened far enough

15Model 230B Miter Mandrel92-0841 : Rev. 050317NOTE:It is highly desirable to mount the Miter Head so that the Angular Offset Pivotpoint is on the sam

16TRI TOOL INC.92-0841 : Rev. 050317NOTE:NOTE:Place the Magnetic Based Indicator Holder onto the Sleeve and energize themagnet.If the existing surface

17Model 230B Miter Mandrel92-0841 : Rev. 050317many times as necessary to achieve the accuracy desired.Once the accuracy requirements have been satisf

18TRI TOOL INC.92-0841 : Rev. 050317EXTENSION KITCapscrew P/N Spacer P/N Length44-0865 9.5" (241.3 mm) 32" (812.8 mm) 36" (914.4 mm)44-

19Model 230B Miter Mandrel92-0841 : Rev. 050317DISASSEMBLY AND ASSEMBLYBack off the four (4) Parallel Offset Adjusting Screws about three full turns e

Copyright 2005Proprietary property of TRI TOOL Inc.No reproduction, use, or duplication of the informationshown hereon is permitted without the expres

20TRI TOOL INC.92-0841 : Rev. 050317Problem: There is a loss of air powerThe air supply pressure is too low.The air filter is plugged.The air line siz

21Model 230B Miter Mandrel92-0841 : Rev. 050317DIAL INDICATOR ASSEMBLY (P/N 50-0015)ILLUSTRATED PARTS BREAKDOWN

22TRI TOOL INC.92-0841 : Rev. 050317Parts List, Dial Indicator Assembly (P/N 50-0015)Item PartNo. No. Description Qty1. 30-0334 BASE, MAGNETIC 12. 30-

23Model 230B Miter Mandrel92-0841 : Rev. 050317MODEL 230B MITER MANDREL ASSEMBLYParts List, Model 230B Miter Mandrel AssemblyItem PartNo. No. Descript

24TRI TOOL INC.92-0841 : Rev. 050317Parts List, Model 230B Miter Mandrel Assembly ContinuedItem PartNo. No. Description Qty12. 33-2069 JACKSCREW ASSEM

25Model 230B Miter Mandrel92-0841 : Rev. 050317Parts List, Sleeve Assembly, Dial Indicator (P/N 46-0475)Item PartNo. No. Description Qty1. 46-0496 SLE

3Model 230B Miter Mandrel92-0841 : Rev. 050317SAFETY PRECAUTIONSWARNING:IN GENERALWhen using rotating head cutting equipment, basic safety precautions

4TRI TOOL INC.92-0841 : Rev. 050317TOOL CAREMaintain tools with care. Keep tools in good operating condition. Sharp tool bitsperform better and safe

5Model 230B Miter Mandrel92-0841 : Rev. 050317Disconnect power supply during setup and maintenance. Use all ‘Stop’ or Shut off’features available whe

6TRI TOOL INC.92-0841 : Rev. 050317GENERAL DESCRIPTIONThe Model 230B Miter Mandrel Head is an accessory option that is used to expandthe versatility o

7Model 230B Miter Mandrel92-0841 : Rev. 050317SPECIFICATIONSWeight: 250 (113.4 kg) Weight will vary with the jackscrew size.Pipe Holding Capacities (

8TRI TOOL INC.92-0841 : Rev. 050317Location IdentificationsParallel OffsetAdjustmentScrew (4)5° Angular OffsetAdjustableJackscrews (8)Angular OffsetPi

9Model 230B Miter Mandrel92-0841 : Rev. 050317MAINTENANCETri Tool Miter Mandrel Heads are precision tools that will perform excellently if theyare wel