92-1333 Rev. 110404Model 236B Single PointTABLE OF CONTENTSCUSTOMER MESSAGE Inside Front CoverSAFETY PRECAUTIONS 3GENERAL DESCRIPTION 6SPECIFICATIONS
10TRI TOOL INC.92-1333 : Rev. 110404Feed GearHousingAssemblyCap ScrewCutter AssemblyGearFlat ScrewGear CoverAssemblyAngular AdjustmentScrew (both side
WARNING:PINCH POINT - Remove the Lathe Stand Feet Supports BEFORE operating.
12TRI TOOL INC.92-1333 : Rev. 110404NOTE:Tool Bit ClearanceFinal Prep LocationPipeClearanceJaw BlockFeedHandlePlateAttach the proper power supply line
13Model 236B Single Point92-1333 : Rev. 110404Remove the machine from the pipe.Check to see if any of the tool bits are dull or broken.Damaged or worn
14TRI TOOL INC.92-1333 : Rev. 110404FEED ADJUSTMENTPut the gearbox into neutral.SETTING THE FEED DIRECTIONSelect the proper hole location on the posit
15Model 236B Single Point92-1333 : Rev. 110404Set the feed direction to neutral by moving the feed knob to the center position.Install the mandrel
16TRI TOOL INC.92-1333 : Rev. 110404Turn the motor on.Let the machine rotate very slowly for one revolution to verify that the tool bit clearsthe ID o
17Model 236B Single Point92-1333 : Rev. 110404CUTTING SPEEDS AND FEEDSPipeSizeRPM for200 in/min(5080 mm/min)RPM for250 in/min(6350 mm/min)RPM for300 i
18TRI TOOL INC.92-1333 : Rev. 110404Use 200 surface inches per minute (5080 surface millimeters per minute) for:Stainless steels in general when no co
19Model 236B Single Point92-1333 : Rev. 110404TOOL BITSTool Bit, Counterbore(P/N 99-1666)A) Insert, Triangular, .030 R(P/N 30-0554)A) Insert, Triangul
Copyright 2011Proprietary property of TRI TOOL Inc.No reproduction, use, or duplication of theinformation shown hereon is permitted without theexpress
20TRI TOOL INC.92-1333 : Rev. 110404MAINTENANCEAll components should be cleaned and coated with a light film of oil prior to use.Daily maintenance sho
21Model 236B Single Point92-1333 : Rev. 110404SPARE PARTSParts List, Recommended Spare PartsItem PartNo. No. Description Qty1. 29-0219 CAM FOLLOWER 12
22TRI TOOL INC.92-1333 : Rev. 110404Problem: The Tool Bit ChattersThe tool bit is loose or overextended.The tool bit is damaged.The tool holder is too
23Model 236B Single Point92-1333 : Rev. 110404Problem: There's a Loss of Air PowerThe air supply pressure is too low.The air filter is plugged.Th
24TRI TOOL INC.92-1333 : Rev. 110404ILLUSTRATED PARTS BREAKDOWN236B SINGLE POINT (P/N 05-0504)1326785910111314124
25Model 236B Single Point92-1333 : Rev. 110404Parts List, 236B Single Point Kit (P/N 05-0504)Item PartNo. No. Description Qty1 24-2707 PLATE ASSY, ADA
26TRI TOOL INC.92-1333 : Rev. 110404PLATE ASSEMBLY, ADAPTER (P/N 24-2707)Parts List, Adapter Plate Assembly (P/N 24-2707)Item PartNo. No. Description
27Model 236B Single Point92-1333 : Rev. 110404CUTTER ASSEMBLY (P/N 82-0141)106121029241117121516199141330262821527232220242539191887
28TRI TOOL INC.92-1333 : Rev. 110404Parts List, Cutter Assembly (P/N 82-0141)Item PartNo. No. Description Qty1. 19-0424 HOUSING, ASSY, GEARBOX 12. 24-
29Model 236B Single Point92-1333 : Rev. 110404HOUSING ASSEMBLY, GEARBOX (P/N 19-0424)12345678910111213141516313
3Model 236B Single Point92-1333 : Rev. 110404SAFETY PRECAUTIONSWARNING:IN GENERALWhen using rotating head cutting equipment, basic safety precautions
30TRI TOOL INC.92-1333 : Rev. 110404Parts List, Gearbox Housing Assembly (P/N 19-0424)Item PartNo. No. Description Qty1. 19-0418 HOUSING, GEAR 12. 20-
31Model 236B Single Point92-1333 : Rev. 110404FEED GEAR HOUSING ASSEMBLY (P/N 82-0226)Parts List, Feed Gear Housing Assembly (P/N 82-0226)Item PartNo.
32TRI TOOL INC.92-1333 : Rev. 110404HOUSING ASSEMBLY, INDEX PLATE (P/N 19-1258)Parts List, Index plate Housing Assembly (P/N 19-1258)Item PartNo. No.
4TRI TOOL INC.92-1333 : Rev. 110404TOOL CAREMaintain tools with care. Keep tools in good operating condition. Sharp tool bitsperform better and safe
5Model 236B Single Point92-1333 : Rev. 110404Disconnect the power supply during setup and maintenance. Use all 'Stop' or 'Shutoff&apos
6TRI TOOL INC.92-1333 : Rev. 110404GENERAL DESCRIPTIONThe Model 236B Single Point is supplied as a kit with modular components as-sembled onto the fac
7Model 236B Single Point92-1333 : Rev. 110404SPECIFICATIONSDESIGN AND OPERATING FEATURESEasy to assemble 236B SP Kit bolts directly to the face of the
8TRI TOOL INC.92-1333 : Rev. 110404The slide assembly has infinitely variable bevel angle adjustments between 0 and37 1/2°.The 236B SP has a total rad
9Model 236B Single Point92-1333 : Rev. 110404INSTALLATIONATTACHING THE MODEL 236B SP KIT TO THE MODEL 236BRemove the Mandrel Assembly, Tool Holder Ass
Comments to this Manuals