Tri-tool 204B Flange Facer User Manual

92-0698 Orig. 970131Model 204B-FF Flange FacerTABLE OF CONTENTSCUSTOMER MESSAGE Inside Front CoverSAFETY PRECAUTIONS 3GENERAL DESCRIPTION 6SPECIFICAT

10TRI TOOL INC.92-0698 : Orig. 970131OPERATIONATTACHING THE MODEL 204B-FF TO THE MODEL 204BRemove the cutting head from the Model 204B BEVELMASTERTM.M

11Model 204B-FF Flange Facer92-0698 : Orig. 970131NOTE:CAUTION:Check for the proper position of the tool holder.Check for the proper position of the t

12TRI TOOL INC.92-0698 : Orig. 970131Damaged or worn tool bits are evident by increased feed pressure, visualobservations, poor surface finish, etc.Re

13Model 204B-FF Flange Facer92-0698 : Orig. 970131Using the 1/4” drive ratchet, run the tool holder to the inward most position.Note any changes in th

14TRI TOOL INC.92-0698 : Orig. 970131WARNING:FEED RATEThe feed rate is .013” per revolution per tripper shaft.INSTALLATION OF THE TOOL BITSTo select t

15Model 204B-FF Flange Facer92-0698 : Orig. 970131CUTTING SPEEDSUse 200 surface inches per minute (5080 surface millimeters per minute) for:Stainless

16TRI TOOL INC.92-0698 : Orig. 970131TOOL BITSP/N Figure Description Cutting Range99-2553* ATool Bit, Flange Facing,Inside Record Finish1.50" to

17Model 204B-FF Flange Facer92-0698 : Orig. 970131TROUBLE SHOOTINGProblem: The Tool Bit ChattersProbable causes:The tool bit is loose or overextended.

18TRI TOOL INC.92-0698 : Orig. 970131Problem: There is a loss of air powerProbable causes:The air supply pressure is too low.The air filter is plugged

19Model 204B-FF Flange Facer92-0698 : Orig. 970131MODEL 204B-FF, FLANGE FACER ASSEMBLYILLUSTRATED PARTS BREAKDOWN1102345768911121315141716

Copyright 2006Proprietary property of TRI TOOL Inc.No reproduction, use, or duplication of the informationshown hereon is permitted without the expres

20TRI TOOL INC.92-0698 : Orig. 970131Parts List, Model 204BB-FF, Flange Facer Assy (P/N 82-0116)Item PartNo. No. Description QtyNOT SHOWN:1. 29-0182 B

21Model 204B-FF Flange Facer92-0698 : Orig. 970131TRIPPER BLOCK ASSEMBLY134576Parts List, Bracket Assy, Tripper (P/N 47-1109)Item PartNo. No. Descript

3Model 204B-FF Flange Facer92-0698 : Orig. 970131SAFETY PRECAUTIONSWARNING:IN GENERALWhen using rotating head cutting equipment, basic safety precauti

4TRI TOOL INC.92-0698 : Orig. 970131TOOL CAREMaintain tools with care. Keep tools in good operating condition. Sharp tool bitsperform better and saf

5Model 204B-FF Flange Facer92-0698 : Orig. 970131Disconnect power supply during setup and maintenance. Use all ‘Stop’ or Shut off’features available

6TRI TOOL INC.92-0698 : Orig. 970131GENERAL DESCRIPTIONIN GENERALThe Model 204B-FF, Flange Facer Kit is supplied as a kit to provide the Model 204BBEV

7Model 204B-FF Flange Facer92-0698 : Orig. 970131SPECIFICATIONSEnvelope, Model 204B-FF, Flange FacerCUTTING CAPACITIESRange: 1.50” to 14.00” diameter

8TRI TOOL INC.92-0698 : Orig. 970131MOUNTING RANGEThe Mandrel for the Model 204B is used to provide a mounting range from 1.25”(31.8 mm) to 4.33” (110

9Model 204B-FF Flange Facer92-0698 : Orig. 970131NOTE:MAINTENANCEIN GENERALAll components should be cleaned and coated with a light film of oil prior